M15 Filters

 

NEW M15 Series Ambient Air Cleaners

bulletMERV 15 Efficiency – 99.9+% @ 0.5 Microns
bulletCleanable
bulletQuiet
bulletMade in USA

Introducing our new flanged, MERV 15 rated, M15 Series Advanced Nano Fiber filters. These filters are offered as “Filters Only” for the do-it-yourselfer or as a unit with U.L. listed, quiet 78-Watt duct booster fans. Either way, 99.9+% of the lung damaging fine wood dust is removed from the air.                       

       

These filters are offered in three sizes. They can be suspended by chain or threaded rod, plenum mounted or placed on a bench. 

Dust collects on the inside of the filter during operation and, when cleaned (in place) with compressed air, the dust falls into the provided dustpan or clear poly dust bag.  In theory, these surface-loading filters will last indefinitely because the dust particles don’t get imbedded into the filter media.  After a brief cleaning, these filters return to “like new” condition. 

With our F14 fans, the C1415 and C1425 filters allow an air flow of 300 and 400 CFM respectively, but, with a customer supplied blower, these filters will flow 1000 and 1400 CFM respectively.  Due to the huge filter area of each filter, the draft produced by the discharged filtered air is barely noticeable, but it is sufficient for adequate circulation within 18 feet.  The smaller C1015 filters are not offered with duct booster fans at this time, but will handle 750 CFM when used with a customer-supplied blower. 

Shop sizing is not an exact science as there are too many variables, but a good rule of thumb is to use one combination F14 / C1415 for a one-car garage if the dust loading at any given time is not too severe.  Using the larger C1425 or your own blower will increase the effectiveness. 

Please see our price sheet. If you have questions or comments, please email us or give us a call.

 

FAN 

F14 (115 Vac Single Phase Only) 

Optional Dust Pan Standard Poly Bag

 

“Out of the Box Fan”, supplied junction box shown (left), optional switches shown.

Illustration Only
Customer installed switch box with optional switches shown.


These are affordable, quiet, energy efficient, UL listed duct booster fans with thermal overload protection and non-sparking aluminum fan blades.  We provide them with styrene pressure rings plus a debris screen for added safety.  The fan assembly fits snugly into the top of both the C1415 and C1425 filters with no need for fasteners. 

We also provide a UL listed wiring conduit box with hardware and extension cord with each fan.  If you want a switch for mounting directly on the fan, we will provide one with a box and switch plate for an additional charge.  We do not ship wired fans.

 

PRICING 

FILTERS:  Made in the USA 

§         C1015:  10” ID, 17”/14” OD, 15” High, Open/Open, Fire Retardant, Nano Fiber complete with two clear poly bags and clamp, 13 lbs………….$135.00 Each 

§         C1415:  14” ID, 19”/18” OD, 15” High, Open/Open, Fire Retardant, Nano Fiber complete with eye bolts, two clear poly bags and clamp, 13 lbs…….$141.00 Each 

§         C1425:  Same as above but 25” High, 18 lbs……………….$152.00 Each 

Adders: 

bullet4 Inch Landis Flange for C1015…………..…..…….$25.00 Each
4 Inch Landis Flange for C1415 and C1425……….$25.00 Each
6 Inch Landis Flange for C1415 and C1425……….$25.00 Each
bulletMetal Dust Pan, Gasket and Springs….….……..…$23.00 Set
bulletMounting Flange on Both Ends……………..………..$22.00 Set
bulletFlex Hose Prices……………………………………... Click Here

 

FANS:  Made in the USA 

§         F14 (115 Vac, Single Phase Only) with debris screen, junction box and short extension cord………….…….$145.00 Each 

Adders: 

bulletOn/Off Switch with box, switch plate and short extension cord………….…$17.00 Set
bullet“Illuminated when on” On/Off Switch with box and short extension cord……$36.00 Set

 

 

Email: sales@WynnEnv.com

Tel (215) 442-9443

Fax (215) 442-9445

     

Wynn Environmental 211 Camars Drive Warwick, PA  18974
www.WynnEnv.com